Home > Error Code > Error 55.a Hp

Error 55.a Hp

Contents

NOTE: The printer reprints the pages that caused the paper jam. by dmzcompute on Dec 30, 2008 at 6:39pm Add comment Please sign in to comment 0 The printer does not give any error messages but it does not detect the duplexer. Replace the duplexer.NOTE: With a worn fuser, the 55.A error usually manifests itself while duplexing, however in extreme cases, the error could appear without a duplexer.3. Replace the ECU. 4.

Home | Error Codes | Hp Printers | Toner Cartridges | Hp Printer Accessories | Hp Plotters Copyright © 2011 Advanced Laser Services, Inc. To check the fuser, turn the printer off and remove the fuser. Verify that there is no issue with the site power. Join your peers on the Internet's largest technical computer professional community.It's easy to join and it's free.

Hp Error Codes

Invalid bus timeout.9 Try using a different printer diver or printing a smaller file.10. ERROR 40 Make sure computer and printer are set to the same baud rates. Simplify the print job. Simplify the print job by removing font changes and/or graphics.

Posted on Jan 29, 2009 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images DLYNAUGH 1 Answer SOURCE: HP Business Jet Can also be caused by a defective DC controller. You can remedy this by replacing the paper guide plate assembly, RG5-2248-030. Hp Error Code 0xc0000185 On my printer, after going through a diagnostic procedure with the HP Chat Tech and concluding a hardware issue I did a bit more research and then took the printer apart.

Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. Press Select button to resume printing, some data loss will occur, you will need to add memory or reduce the complexity of the print job. I swapped a known working/detected duplexer and it was not detected. find more Check connections to DC controller - replace main motor 4L/4 Main motor problem, check gear train for binding.

Take a sharp tool, like a razor blade and scrape the buildup off these edges. Hp Fax Error Codes Whats left is the wire harness or DC controller. Reseat the card and if available, swap with a known working card. No hard feelings.

Hp Computer Error Codes

Include an image. Back back to top How did we do? Hp Error Codes I kinda dont go for the incompatablity solution becuase most machines have these in there machines for quite some time before the error accures so why would it fail all the Hp Error Beep Codes Defective Paper Control Sensor PCB - These do fail and will need to be replaced.

Plug the printer into a wall outlet and see if this resolves the problem. 2 If the printer is already plugged into a wall outlet, try another power source in the Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations Let's discuss about it:1) If the POWER light is flashing green, then your printer is now warming up or performing maintenance procedure (replacing cartridge/tank) or cleaning print head, just wait a On older style printers this is often caused by a bad main motor. (Older style printer being printers with halogen heating elements in the fuser - 4, 4+, 5, 4si, 5si, Hp Error Code Oxc4eb827f

If the message persists, reseat the fuser. Improperly seated SIMMs or font cartridge - remove, check/clean contacts re-install and try again. controller to the fuser ass'y.3. Check the connector inside the machine.

How did we do? Hp Officejet Error Codes At the time I was an ASP and called HP about it. How did we do?

Already a member?

Nov 24, 2008 | Epson Stylus Photo R300 InkJet Printer 1 Answer BJC55 Printer not printing There are some possibilities due to the above phenomena. This can happen when printing a FAX document formatted for A4 size paper. Change wiring harness from the D.C. Hp Error Code 0xe0ef0003 Caution needs to be used when installing the new assembly - be careful of the sensor flag spring! 5Si - Can be caused by field replaceable units (FRU's) not installed correctly.

by unknown on Sep 4, 2008 at 8:08am Add comment Please sign in to comment 0 we mainly print large certiticates on cardstock, the words are showing up faded; we changed Replace the formatter board.   (On the 5si, 8000, 8100 this could be a fuser problem. Printer Works RM1 9371 000 DC Controller As M775 mfp HP LaserJet DC Controller For M775 Printer RM1 8898 - USD70+shipping Mar 18, 2016 | HP LaserJet M775DN Laser Multifunction... 2 here is the lin for additional solution:http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&objectID=bpl12422&jumpid=reg_R1002_USEN#A46 Posted on Oct 26, 2009 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images

Showing results for  Search instead for  Do you mean  or Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Topic to the Also try printing from a different application. Reseat DIMM, then Formatter - Replace or flash DIMM then formatter Back back to top How did we do? Posted on Jul 09, 2008 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images speters9971 1 Answer SOURCE: printer will not

Try replacing the fuser.) 56.X PRINTER ERROR An incompatible combination of input/ output bins was selected. The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications. 51.X PRINTER ERROR A loss of beam-detect Anyone have any ideas on what I can do to fix this or any other tricks I can try? Remove the jetdirect first though so you dont reset it.

Is the computer powered off! You can't post answers that contain an email address. by unknown on Oct 28, 2008 at 7:45am Add comment Please sign in to comment 0 As always check and verify that what you are using is within the quide lines If you cycled the power, it would work for a little while, but eventually come up with the error again.