Home > Error Accessing > Error Accessing Directory Object

Error Accessing Directory Object

Contents

This one will serve as one more addition to the long list of solutions which developers just like me have recorded over their experiences. The error might have been due to a temporary failure. This is probably caused by your system reaching its maximum number of processes. Its also has the ability to monitor the health of individual VMware virtual machines. More about the author

A new attempt might succeed. Description: See Chapter 7, NIS Troubleshooting, in System Administration Guide: Naming and Directory Services (DNS, NIS, and LDAP) for possible causes. See ASP.NET Ajax CDN Terms of Use – http://www.asp.net/ajaxlibrary/CDN.ashx. ]]> United States English English IBM® Site map IBM Possible Cause: Insufficient memory.

Error Accessing Product Object Method

See also Chapter 7, NIS Troubleshooting, in System Administration Guide: Naming and Directory Services (DNS, NIS, and LDAP). Thanks to readers sending in information on this error code, we are slowly building up a library of problems, and even more importantly, solutions. Action: Enter a valid value. Special Instructions None.

Description: The most likely causes for this message are: Bad or incorrect parameters being passed to the xdr_directory_obj routine. The severity of this message depends on what level of security you are running. The rpc.nisd should have aborted. Robocopy Error Accessing Source Directory Possible Cause: The WebAccess Agent does not have sufficient rights in the domain directory structure.

Development needs to further test this (Reported to Engineering)For eDirectory environments: User's ID shows up in relation in to the extra attribute of 'samAccountName', where it should only be seen as Error Accessing Product Object Method On Module Pref_save If I am wrong, and you want to go down that route at leaset pay with card, that way there is a chance that you can get a refund if I This requires some action on your part: Check to make sure that servername has DES credentials. https://communities.vmware.com/thread/451362?start=0&tstart=0 Start GroupWise WebAccess and restart the other GroupWise agents.

Action: Use ConsoleOne to reenter the configuration information. Robocopy Error Accessing Destination Directory Action: Have the user log in through the GroupWise WebAccess login screen. Action: Make sure the user knows his or her GroupWise user ID and enters it when logging in. Possible Cause: The uid.conf file has been deleted.

Error Accessing Product Object Method On Module Pref_save

Possible Cause: The user did not enter a password when logging in. http://www.ibm.com/support/docview.wss?uid=nas2MA34642 Description: This message is generated by the NIS+ error code constant: NIS_S_NOTFOUND. Error Accessing Product Object Method Master server busy full dump rescheduled Description: This message indicates that a replica server has been unable to update itself with a full dump from the master server because the master Error Accessing External Object Property Description: NIS+ was unable to transfer the NIS map for this table to the NIS+ database.

Action: Make sure the startup file is in the same directory as the WebAccess Agent program or that filename includes the full path to the file. my review here Browse down the tree to Console Root -> Component Services -> Computers -> My Computer4. authdes_seccreate: out of memory Description: See Chapter 7, NIS Troubleshooting, in System Administration Guide: Naming and Directory Services (DNS, NIS, and LDAP) for information on insufficient memory problems. Seems that all words, which are different than the names of the existing IWAM_* and IUSR_* users are OK. Error Accessing External Object Property Powerbuilder

NIS+ server not responding Description: See Chapter 7, NIS Troubleshooting, in System Administration Guide: Naming and Directory Services (DNS, NIS, and LDAP) for possible causes. Description: This message is returned if NIS+ is not installed on a machine or if for some reason the file /var/nis/NIS_COLD_START could not be found or accessed. See Using WebAccess Startup Switches in WebAccess in the GroupWise 8 Administration Guide. click site Additional information can be obtained from the write routine's man page.

checkpoint_log: Unable to checkpoint, log unstable. Call "userdirectory.retrieveusergroups" For Object "ha-user-directory" replica_update: WARNING: last_update (directoryname) returned 0! See WebAccess Security Requirements in Installing GroupWise WebAccess in the GroupWise 8 Installation Guide.

Action: Make sure the user knows his or her mailbox password and enters it when logging in.

log_resync: Cannot truncate transaction log file Description: An attempt has been made to checkpoint the log, and the rpc.nisd daemon is trying to shrink the log file after deleting the checkpointed Run ps -ef | grep rpc.nisd to see if rpc.nisd is still running. See Chapter 7, NIS Troubleshooting, in System Administration Guide: Naming and Directory Services (DNS, NIS, and LDAP) for further information. A General System Error Occurred Error Accessing Directory Can't Bind To Ldap Server For Domain One name is not allowed to be in both of these tables.

V5R4M5 Recompile........................................... Description: Table context. Click on Access Permissions ' Edit Defaulta. navigate to this website WEBACC: Running the agent with conflicting effective users Source: GroupWise WebAccess Agent for Linux.

APAR (Authorized Program Analysis Report) Abstract LIC-MSGCPFB620 Unexpected error accessing an IFS object Error Description Conversion of IFS directories from *TYPE1 to *TYPE2 results in MSGCPIA08E RC1. Every attempt to use the component inside the IIS resulted in the error being thrown, while using it from my unit tests presented no issues. CKString is the property of chilkat.com I hope you find these steps useful. Possible Cause: The GroupWise WebAccess user did not perform any actions in GroupWise WebAccess during the timeout interval.

Re: ESXi 5 not allowing me to bind to LDAP bojanpopovic Jul 18, 2013 5:38 AM (in response to Chlsmith) Same thing happened to our servers. Possible Cause: Heavy WebAccess usage for the number of threads allocated to the WebAccess Agent. Note that, the third-party component is added as a reference to the VB.NET library project and not the web project. Security exception on local system.

If you are not the owner of the domain or as a group member of the parent domain, rerun the script as the owner, or as a group member of the See the nis_names and nis_names man pages for additional information. Notify me when an APAR for this component changes. In the case of nis_list, if the client specifies a callback and the server does not have enough resources to handle the callback.

RPC failure: “RPC failure on yp operation. Possible Cause: The WebAccess Agent does not have rights to write to files in the log file directory or the disk is full. The value was changed to 'EVERYONE' and the error has disappeared. error receiving zone transfer Description: DNS error message.

If it is not, then start it, and then run keylogin. Guy Recommends: SolarWinds Engineer's Toolset v10 This Engineer's Toolset v10 provides a comprehensive console of 50 utilities for troubleshooting computer problems. Incidentally, insufficient rights or priveleges is a common thread of other types of Access Denied problems in general, and code 80070005 in particular. Description: This message indicates that you typed the wrong network password.

Possible Cause: The user did not enter a GroupWise user ID or full name when logging in. The user specified in the uid.conf file does not match the user specified in the uid.run file. Description: This message is generated by the NIS+ error code constant: NIS_NAMEEXISTS. These steps above may need modifications based the type of IIS user account that is used in your environment.