Home > Error 6 > Error 6 Server_2 No Such Device Or Address

Error 6 Server_2 No Such Device Or Address

Please type your message and try again. 1 2 Previous Next 22 Replies Latest reply: Oct 31, 2012 3:59 AM by dynamox Incoming Ping EMC with Servers antonio101980 Oct 30, 2012 No specific storage requirements. VNX support IEEE 802.1Q VLAN tagging on network devices defined by the device prefix ace, cge, fge, and fxg. VLSMs allow for better use of the available address space by allocating the appropriate number of host addresses per subnet and reducing the number of unused addresses in each subnet. 2 http://axishost.net/error-6/error-6-terminal-server-printer-driver-redirection-wizard-encountered.php

Please check and suggest me what should i have to do to resolve this issue.       The operation failed due to a communication problem with the Data Mover : Buy the Full Version NetworkingUploaded by gonna009Computer Network12 viewsDownloadEmbedSee MoreCopyright: Attribution Non-Commercial (BY-NC)List price: $0.00Download as PDF, TXT or read online from ScribdFlag for inappropriate content Documents similar to NetworkingEUChinaGRID IPv6 Replies, therefore, must be sent through the same interface as the incoming requests. Published (2014-10-15 02:08:00) Hi Sathish,   I think you can try this document:   https://community.emc.com/docs/DOC-22434   Thanks Jyothi Rakesh Pandey 1 user's latest post: Unable to Join CIFS server into... https://community.emc.com/thread/164713?tstart=0

All rights reserved. Packet Reflect works as follows: When Packet Reflect is enabled, the Data Mover does not examine the route, Neighbor Cache, and ARP tables when sending outbound packets from established connections. I've tried searching the net for solutions, and tried most of them, but most of them are just different strings to insert into /etc/fstab.

For each IP address, the Data Mover keeps only one associated MAC address in the ARP table. hcart TLD(8) DRIVE=10 /dev/rmt/c22t0d0BESTnb DOWN When The routed daemon listens for RIP V1 and V2 messages on the network and changes the routing table based on the messages. Power BI on-premises data gateway.

Differences between IPv4 and IPv6 Table 3 on page 23 shows some common differences between IPv4 and IPv6. If the VLAN ID of an interface is set to zero, packets are sent without tags. Supporting high-availability devices Normally, Packet Reflect determines the interface for the reply packets. page TCP/IP routing and workload balancing ERserver iseries TCP/IP routing and workload balancing ERserver iseries TCP/IP routing and workload balancing Copyright International Business Machines Corporation 1998, 2001.

Not the answer you're looking for? US More information EMC Data Domain Boost for OpenStorage EMC Data Domain Boost for OpenStorage Version 3.0 Administration Guide 302-001-271 REV. 03 Copyright 2015 EMC Corporation. Topics included are: System requirements on page 12 Restrictions on page 12 User interface choices on page 12 Related information on page 13 Configuring and Managing Networking on VNX 7.0 1112 The speed and duplex cannot be modified for a fiber connection (ace, fge, and fxg).

iseries. http://unix.stackexchange.com/questions/238795/mount-error6-no-such-device-or-address The IP interfaces define the IP addresses that the device presents to the network. The neighbor cache maintains a list of neighbors by their global unicast address, link-layer address, whether the neighbor is a router or host, and the state of the neighbor entry, such Show more post info Size: 467 bytes Customize: Reply 10: Re: Unable to Join CIFS server into Domain in VNX VG8 gateway dynamox replied 1 year, 12 months ago i am

There are two ways to work with VLANs: Configure a switch port with a VLAN identifier and connect a VNX port to that switch port. When Packet Reflect is disabled, the Data Mover examines the route and ARP tables when sending outbound packets from established connections. Configuring and Managing Network High Availability on VNX provides information about high-availability devices. Subnet masks Broadcast addresses Yes Yes No.

Buy the Full Version You're Reading a Free Preview Pages 61 to 76 are not shown in this preview. If you can ping that but cannot ping anything outside of that subnet (i.e. This enables the server to connect to multiple VLANs and their corresponding subnets through a single physical connection. To check for more recent editions More information Data ONTAP 8.2.

Link-local interfaces are reserved for core IPv6 protocols (such as Duplicate Address Detection, Neighbor Discovery, Router Discovery, and ICMP6). Mounting a NAS is pretty new to me. In NFS environments, you can use the server_export command to protect or limit user access.

Please try the request again.

Noncontiguous network masks are masks without a continuous stream of 1 bit. Link-local addresses Link-local addresses are used primarily for administrative purposes, such as address resolution and duplicate address detection. Note: IPv6 does not support broadcast addresses. more stack exchange communities company blog Stack Exchange Inbox Reputation and Badges sign up log in tour help Tour Start here for a quick overview of the site Help Center Detailed

Re: Incoming Ping EMC with Servers Rainer_EMC Oct 30, 2012 9:01 AM (in response to antonio101980) Why are you getting that Error 6 ?I think it means that either your DM ND automatically updates the Neighbor cache. Automatic default router configuration 2728 Concepts Routing table The routing table determines the next hop when a Data Mover is sending a packet. Labels: 7.1.x and Earlier Backup and Recovery Basics Error messages NetBackup Tip-How to Troubleshooting 0 Kudos Reply 1 Solution Accepted Solutions Accepted Solution!

Telephone: +1(408) 822-6000 Fax: +1(408) 822-4501 Support telephone: +1(888) 4-NETAPP Web: www.netapp.com More information 2016 © DocPlayer.net Privacy Policy | Terms of Service | Feedback Veritas.com Support Veritas Open Exchange Login To view just ipv4 or just ipv6 use the -ip4 or -ip6 options. Because of this dependency, you cannot delete the default link-local interface. These presentation strings are not saved.

The backup router does not need to wait until the routing table entries are updated by the RIP. Network Management Guide For 7-Mode. By default, Packet Reflect is enabled. In this method, the switch ports for servers, including VNX, are configured to include VLAN tags on packets sent to the server.

Part of it was what Niclai indicated and then I updated the drive path with the device file name using tpconfig -update. smbclient -L 192.168.0.7/volume1/NetBackup displays the details of my NASWhen I atttempt to mount using below command:$ sudo mount -t cifs //192.168.0.7/volume1/NetBackup /mnt/NAS -o user=XXXXXX,password=XXXXXXI get the below error:mount error(6): No such Topics: Active | Unanswered Index »Newbie Corner »[SOLVED]Error: "mount error(6): No such device or address" mounting NA Pages: 1 #1 2015-10-29 19:30:17 ArchArching Member Registered: 2015-10-25 Posts: 14 [SOLVED]Error: "mount error(6):